2008 Ford Bantam Rocam 1.6 Missfire

Asked by IAmEttiene Dec 27, 2023 at 03:57 PM about the Ford Bantam

Question type: Maintenance & Repair

Hi Guys, My 1.6 Bantam Rocam 2008 misses slightly when cold and a lot when
it reaches peak heat. i have installed new Spark Plugs, HT Leads, CoilPack,
Petrol Pump, Head Gasket and problem is still there. Please Help. Thanx

2 Answers
16,475

Guru97FK8 answered 3 months ago

Check the Wiring harness and the three pin connector at the coil pack. As these vehicles age so some of the wiring might become brittle. We have had one Rocam that the section of the harness to the three pin connector plug, that there was an intermittant open circuit at one of these wires. To test this, dis connect the Computer box, Use an Multu-meter set on Ohms , connect the one terminal of the multi-meter to the ECU side pin and connect the other to the Coil pack side terminial and move the wires about and see if there is any open circuit. Next, try the other wires. To check short to ground, Ground the one multi-meter wire and probe firs the one wire and then the next. If there is a readying during this test, you know that one of the return wires is shorting to ground..

1 people found this helpful.
Mark helpful
16,475

Guru97FK8 answered 3 months ago

Please find below links for 2002 Bantam workshop Manuals and Wiring Diagrams. These diagrams can be down loaded onto you PC https://www.manualslib.com/manual/1106266/Ford-2002-Bantam.html#manual https://elektrotanya.com/ford_bantam_2002_wiring_diagrams.pdf/download.html

Mark helpful

Your Answer:

Related Questions

  • 2008 Ford Bantam Rocam 1.6 Missfire 2 Answers

    Hi Guys, My 1.6 Bantam Rocam 2008 misses slightly when cold and a lot when it reaches peak heat. i have installed new Spark Plugs, HT Leads, CoilPack, Petrol Pump, Head Gasket and problem is still t...

    Ford Bantam

    -

    Maintenance & Repair

  • Bantam 2008 rocam 1.3i 3 Answers

    I have a 2008 Bantam rocam 1.3i The battery is being discharged when switched off and stands overnight The battery is new and when fully charged retains charge if positive terminal is disconnected. O...

    Ford Bantam

    -

    Maintenance & Repair

  • Ford bantam rocam 2010 2 Answers

    Hi everyone can you please assist On my Ford bantam 1.3 rocam, I was changing the spark plugs yesterday when we done with changing the spark plugs we attempt to start,it didn't start but the engine...

    Ford Bantam

    -

    Maintenance & Repair

  • Ford bantam rocam engine . Crank no start 1 Answer

    Hi. I have a 2008 ford bantam rocam 1.3. It cranks and has fuel and spark but no start. I'm using a 1.6 ecu for pre 2007 bantams. I also changed the flywheel to match the ecu 36-1 teeth. Does the ...

    Ford Bantam

    -

    Maintenance & Repair

  • Ford bantam 1.6 2006 3 Answers

    Hi, I bought 2006 ford bantam at SMD in September ROCAM 1.6 engine, computer box is 1.3. car was running until few days ago, the engine is cranking but not starting. the coil, sparks and fuel filt...

    Ford Bantam

    -

    Maintenance & Repair

Shortcuts

Search Ford Bantam Questions

CarGurus Experts

  • #1
    Guru97FK8
    Reputation
    15,170
  • #2
    Janus Welgemoed
    Reputation
    1,140
  • #3
    MrRocket12
    Reputation
    1,120
View All

Find great deals from top-rated dealers

Search

Content submitted by Users is not endorsed by CarGurus, does not express the opinions of CarGurus, and should not be considered reviewed, screened, or approved by CarGurus. Please refer to CarGurus Terms of Use. Content will be removed if CarGurus becomes aware that it violates our policies.