2003 dodge intrepid se wont turn over

335

Asked by punchincamel Feb 18, 2013 at 11:01 PM about the 2003 Dodge Intrepid SE FWD

Question type: General

when i turn the key to the on position all the lights and bells work. i turn the key to the start possition
and get nothing. No fuel pump kicking on not even a relay clicking sound when i hook the obdII to
the
car it reads NO LINK car is getting ready to be scraped if i cant get it figured out.had one person tell
me
it may be a broken wire in between the key switch and the computer

37 Answers

You must do some testing then, follow the schematic test each wire coming off of the ignition switch and it's destination. You'll need a good fifteen feet test wires- meticulous yes, but there is no other way. Nose to the grindstone, one wire at a time~

2 people found this helpful.
335

i have tried changing the steering column with no help there would it be a ground wire possibly?

1 people found this helpful.

Keep seeing references to the key as controlling everything. Are you using a different key then you usually do. Apparently these things are coded.

1 people found this helpful.
Best Answer Mark helpful
335

i have the factory sentry coded key without the key fob but still without the coded key the car should still start then shutdown after 2 sec. i get nothing from the started or fuel pump

feel sad that I wasn't able to solve your problem and admit defeat. Perhaps a guy like DavidH25, tenspeed, smoothpapa any of the top three gurus would tackle this in a sec. If we are out there long enough they will help!

llregal is a dodge afficianado-like a bulldog grabs onto the problem and researches it with printed media, then churns out a rather verbose explaination if he, a kind of creature that gets ahold of this we will see dissertations aplenty...but don't get on his bad side...

335

any help i can get i appreciate and no i wish it was still under warranty makes me mad the car ran when i got it and then one day i shut it off and this happens hope its not in the anti-theft

one of these other chaps will help you. common sense barnyard mechanic has limited resources...some of these fellows will dish out nothing but right answers...hold onto your hat...if we wait long enough...too bad we couldn't put a RED FLAG on your problem...I'll see about that too=

2 people found this helpful.

Honestly I couldn't tell you if the Electronic Control Unit is responsible for security and more...completely out of my league..aplogies all around...just here to help anyway I can.

Hi fellas and good morning. The ECU is responsible to that^^ above post by Bob, and "no link" means there is no link from OBDII port to the brain of the car, the ICM or the ECM where the faults are stored waiting to be read. Not 'no link' from key transponder to ICM to start the car. No link means the scan tool is either not getting a signal from the port or the faults have been erased, which can happen if the battery is disconnected and it's just empty, no faults in there. They were lost when you changed the steering column. Which leads me to: did you swap the entire steering column and why? (I smoke those punch in Camel Menthols) anyway this

2 people found this helpful.

When you changed the column, and with it a new key, the ECU must 'learn' the new codes. Insert the key that you would like to program into the ignition of your Dodge and turn the key to the "On" position. Leave the key in the "On" position for 10 minutes and 30 seconds. Turn the key back to the "Off" position after the 10:30 span has elapsed. You must do this within 45 seconds and then repeat the process two more times, leaving the key "On" for 10 minutes and 30 seconds each time. Turn the key back to the "Off" position after the third cycle. Turn the key "On" and start the vehicle. Your key will now be successfully programmed and ready for use. Programming Additional Keys Insert your programmed key into the ignition and turn the key to the "On" position for five seconds. Return the key to the "Off" position after five seconds and then remove the key from the ignition. Insert a new key into the ignition within five seconds, turn it "On" for five seconds and then return it to the "Off" position. Turn the key back to the "On" position and the programming will be completed.

5 people found this helpful.

I hope that helps. then when you get it running, drive a few miles to let the ECU store whatever faults there may be, then scan it again.

1 people found this helpful.
335

ok i will try these options today, and i changed the steering column due to i had a mechanic tell me the problem im having could be a broken wire between the key switch and the ecu..i changed the entire column and got nowhere i will today re- program the key witch i have the original and the new one from the column

335

ok have found out that this car has not got a sentry/skimm key system. if i had this system my key should be grey right? i have a black key, and also there is no anti- theft on this car that im aware of there are no indicator lights on the dash that would tell you its armed or not

1 people found this helpful.

I just called my sister on the phone, because she has Dodge Durango, Her key is black, for a 2005.. Yes you do have ant theft, that is what key transponder codes are for.

335

anyways update: i hot-wired the auto shut-down relay and to my surprise all my relays seemed to work except for still the fuel pump and starter relay if i hot-wire the fuel pump relay i get fuel and then hotwire the starter relay i get it to turnover but still no spark . i still cant get my ignition to do the work

335

The Auto Shutdown Relay (ASD) - actually, this rarely breaks, but when it does, the engine stays off. One purpose of the auto shutdown relay is to avoid "dieselling." It kills all fuel delivery and spark. The ASD can be triggered by a broken wire or short in another place -e.g. the fuel pump

please 'camel, you are interesting sort of person. Can we not put your face up there dig into your wallet, your picture IS handy,,,,stop it. make with the goods~

I am certainly on a learning curve here. punch, Dodge had to have changed the way they do it in 'twixt 03 and 05 then. I been watchin' and learnin' sorry for the mis info

335

they are the same ignition switch but the immobilizer is an add -on for the anti-theft that slides over the ignition switch

1 people found this helpful.

Your Answer:

Intrepid

Looking for a Used Intrepid in your area?

CarGurus has thousands of nationwide listings and the tools to find you a great deal.

Postal Code:

CarGurus Experts

  • #1
    Michael Kane
    Reputation
    2,010
  • #2
    Afsheen Dar
    Reputation
    810
  • #3
    Paul
    Reputation
    500
View All

Find great deals from top-rated dealers

Search

Content submitted by Users is not endorsed by CarGurus, does not express the opinions of CarGurus, and should not be considered reviewed, screened, or approved by CarGurus. Please refer to CarGurus Terms of Use. Content will be removed if CarGurus becomes aware that it violates our policies.